DESCRIPTION
SEALPROOF is a durable NON-VOC visible film with superior adhesion to the following surfaces: wood, gelcoat, steel, carbon-graphite, fiberglass, aluminum and all types of composites. SEALPROOF gives a matte surface, for parts requiring a high gloss finish, SEALBRITE or SEALER GP should be used. SEALPROOF, when applied in conjunction with WATERSHIELD Release Agent, provides multiple releases and reduces down time due to cleaning. For a totally solvent-free mold release system, use WATERCLEAN, SEALPROOF and WATERSHIELD.
SEALPROOF benefits are:
| * ENVIRONMENTALLY SAFE | * Thermal Stability (1 hour at 650 F.) |
| * No solvents or alcohol | * Highly Penetrating |
| * No CFC’s, VOC’s, or ODC’s | * Air Dry or Heat Cure |
| * Non-flammable carrier | * Fast cure |
| Appearance & Odor | Opaque liquid with bland odor |
| Carrier | Water |
| Flash Point [C.C] | None |
| Coverage | Approximately 1200 Sq. Ft./Gallon |
| Wt/Gallon | 8.5 lbs/Gallon |
| Cure Requirement | Ambient or heat |
SEALPROOF USES
overcomes micro-porosity in mold surfaces
eliminates the break-in time for new molds and/or tools
extends the number of releases of a releasing agent
reduces mold/tool down time
restores a uniform surface when used over a mold repair or patch
SURFACE PREPARATION
Before applying SEALPROOF, all previous waxes or oils should be removed using WATERCLEAN.
MOLD CLEANING
WATERCLEAN has been developed to replace solvent-based cleaning solutions. WATERCLEAN is a stand-alone product that can be used to clean and prepare molds and/or parts when further processing is needed. WATERCLEAN provides an effective alternative for the removal of surface contaminants without harming the working surface of the mold and/or part. WATERCLEAN is RECOMMENDED FOR MOLD PREPARATION BEFORE APPLICATION OF AN APPROPRIATE MOLD SEALER.
HOW TO APPLY SEALPROOF
SEALPROOF requires only a thin coat, which is easily applied by wiping with a paper towel. It can be applied by brushing with a soft, fine-bristled brush. Spraying is not recommended.
Application should be made to a small area and then repeated until entire surface is completely coated.
1. Apply a thin coat of SEALPROOF.
2. Air-dry for 30 minutes (minimum).
3. Apply 2nd thin coat of SEALPROOF.
4. Air dry for 60 minutes before applying WATERSHIELD or WATERSHIELD V release agent.
NOTE: A heat gun can be used to speed drying time or mold/tool can be placed in an oven for a minimum of 15 min. at 150°C. SEALPROOF can be applied to the heated surface.
TO NEW TOOLS
Additional coats of SEALPROOF are necessary to seal a new tool. For polyester tooling, wait at least 24 hours for the styrene to dissipate before applying the sealer. For porous tools, apply 6 - 8 coats using the instructions above, only the last coat of SEALPROOF. For microporosity, 4 coats of SEALPROOF may be adequate.
NOTE: Do not attempt to apply SEALPROOF over any release agent. Keep tightly closed when not in use.
STORAGE & SHELF LIFE
Store in a dry area in the original closed container. DO NOT store at elevated or freezing temperatures. Shelf life – 12 months providing original container remains unopened.
SAFETY DATA
Material safety data sheets are available for all ZYVAX products and should be consulted prior to use of product.
SHIPPING DATA
| DOT SHIPPING NAME : | None |
| DOT HAZARD CLASSIFICATION: | None |
| DOT I.D. NUMBER: | None |
PACKAGING
SEALPROOF is available in the following sizes:
1-U.S. gallon can
5-U.S. gallon pail
NOTE: THE INFORMATION CONTAINED HEREIN IS BELIEVED BY DE-COMP COMPOSITES, INC. TO BE ACCURATE. HOWEVER, NO WARRANTY EXPRESSED OR IMPLIED IS MADE REGARDING THIS DATA , THIS MATERIAL, OR RESULTS THERE FROM WHETHER USED IN ACCORDANCE WITH OUR INSTRUCTIONS OR NOT. THE USER SHALL MAKE HIS/HER OWN TESTS TO DETERMINE SUITABILITY OF THIS MATERIAL FOR HIS/HER PARTICULAR PURPOSES, IN ANY EVENT, DE-COMP’S LIABILITY SHALL BE LIMITED TO THE PURCHASE PRICE OF THE MATERIAL.
| Home Page | Product List | Top of Page | E-mail De-Comp |
