DE-COMP COMPOSITES, INC.

  ZYVAX WATERSHIELD

WATERSHIELD

DESCRIPTION
WATERSHIELD can be considered a UNIVERSAL release.  It is a high performance polymer coating that has been created to give multiple releases while exceeding the most demanding environmental requirements.  WATERSHIELD has no VOC’s and is so versatile it can be used for most molding operations and is preferred for application directly on warm mold tools.  For a totally solvent-free mold release system, use WATERCLEAN, SEALPROOF and WATERSHIELD.   WATERSHIELD V should be used for high temp applications when spraying is desired, and when applications for each part are specified

 WATERSHIELD  benefits are:

WATERSHIELD USES

• recommended for releasing epoxies, phenolics, polyester resins, polyamides, polybismaleimides, various rubbers and elastomers.

• specified for applications where the use of flammable products or solvent based materials are not desired.

 
SURFACE PREPARATION
Before applying WATERSHIELD, all previous waxes or oils should be removed using WATERCLEAN, then a suitable mold sealer should be applied.  If surfaces have been coated with a semi-permanent release agent, it may be possible to simply solvent wipe, dry, and apply WATERSHIELD.  A test patch should be done to confirm this possibility.

MOLD CLEANING
WATERCLEAN has been developed to replace solvent-based cleaning solutions.  WATERCLEAN is a stand-alone product that can be used to clean and prepare molds and/or parts when further processing is needed.  WATERCLEAN provides an effective alternative for the removal of surface contaminants without harming the working surface of the mold and/or part.  WATERCLEAN is RECOMMENDED FOR MOLD PREPARATION BEFORE APPLICATION OF AN APPROPRIATE MOLD SEALER.

MOLD SEALING
For wood, gel coat, steel, carbon-graphite, fiberglass, polyester, epoxy, urethane, and aluminum use SEALPROOF for a durable, highly visible, penetrating film with superior adhesion and especially with poor or porous surfaces.  Additional water based Zyvax sealers would be SEALMATTE (non-glossy surface) and SEALBRITE (high gloss surface). 

 
HOW TO APPLY WATERSHIELD

1.      Apply one light coat of WATERSHIELD to a small area of the mold using a Bounty paper towel, or hand sprayer.

2.      Wait approximately 2 minutes, and then lightly wipe over the mold surface using a separate clean Bounty paper towel.

3.      Wait 15 minutes and apply the second coat of WATERSHIELD.

4.      Wait approximately 2 minutes, and then lightly wipe over the mold surface using a separate clean Bounty paper towel.

5.      Allow a set time of 30 minutes before using mold.  If application has been made to a warm surface, a shorter waiting period is needed.  The use of heat (hot air, heat gun, oven) can enhance performance.

6.   For touch up apply a single coat of WATERSHIELD as above and continue processing.

STORAGE AND SHELF LIFE
Store in a dry area in the original closed container.  DO NOT store at elevated or freezing temperatures. Shelf life – 12 months providing original container remains unopened.

SAFETY DATA
Material safety data sheets are available for all ZYVAX products and should be consulted prior to use of product.

SHIPPING DATA

PACKAGING
WATERSHIELD is available in the following sizes:

                1-U.S. gallon can
                5-U.S. gallon pail
                55-U.S. gallon pail

PRINTABLE VERSION

NOTE: THE INFORMATION CONTAINED HEREIN IS BELIEVED BY DE-COMP COMPOSITES, INC. TO BE ACCURATE. HOWEVER, NO WARRANTY EXPRESSED OR IMPLIED IS MADE REGARDING THIS DATA , THIS MATERIAL, OR RESULTS THERE FROM WHETHER USED IN ACCORDANCE WITH OUR INSTRUCTIONS OR NOT. THE USER SHALL MAKE HIS/HER OWN TESTS TO DETERMINE SUITABILITY OF THIS MATERIAL FOR HIS/HER PARTICULAR PURPOSES, IN ANY EVENT, DE-COMP’S LIABILITY SHALL BE LIMITED TO THE PURCHASE PRICE OF THE MATERIAL.

Page Last Modified:  07/10/2005